15BBL brewery equipment and 15BBL fermenation tank in Russia
Brewhouse Components
Brewhouse
Our standard 15 barrel brewhouse offering includes a 15 barrel steam fired brew kettle matched up with a 30 barrel hot liquor tank and 15 barrel mash tun. The 30 barrel HLT allows the brewer to make double batches in a day to increase production. The brew kettle has tangential side port for optional whirlpool process following the boil. The vessels are oversized so the brewer can deliver a full 15 barrels of wort to the fermentation vessels. Stainless steel dimple jackets are utilized on the vessels to maximize steam energy transfer into the wort, decreasing wait time before boiling. All three vessels are fitted with internal clean in place ball system.
All pumps, valves, heat exchanger, and process piping are included to provide a complete system.
Grant/Hop Back
Our 25 gallon grant/hop back provides an accessible location to take wort samples during the lautering process. The grant is also used by many brewers to dry hop their wort after the boil is complete. High and low level sensors inside the vessel control the main transfer pump to maintain the correct flow in the process. The grant/hop back has a removable wedge wire false bottom for easy cleaning and sanitation.
Brewers Platform
The brewer’s platform is custom fitted to match each brewhouse system. Made from a perforated, non-slip fiberglass material the brewing platform allows the brewer easy access to the control panel and manways on top of the vessels. The brewhouse system has been designed to minimize elevation and only requires three steps from ground to top of platform.
Control Panel
The brewing control panel allows the brewer to set HLT temperature setpoint and monitor mash tank and brew kettle temperatures. Transfer pump mode and speed are also controlled at the panel. Each control panel is built in the USA, prewired and tested in our shop, and is UL listed for the specific job location.
Keg Washer The custom-fitted keg washer allows 2 kegs to be cleaned and sanitized at the same time. The keg washer rolls into place along the front of the brewhouse and utilizes the main transfer pump to circulate cleaner through the kegs. An experienced operator can clean up to 20 kegs per hour with this system.
Brewhouse Components
Brewhouse
Our standard 15 barrel brewhouse offering includes a 15 barrel steam fired brew kettle matched up with a 30 barrel hot liquor tank and 15 barrel mash tun. The 30 barrel HLT allows the brewer to make double batches in a day to increase production. The brew kettle has tangential side port for optional whirlpool process following the boil. The vessels are oversized so the brewer can deliver a full 15 barrels of wort to the fermentation vessels. Stainless steel dimple jackets are utilized on the vessels to maximize steam energy transfer into the wort, decreasing wait time before boiling. All three vessels are fitted with internal clean in place ball system.
All pumps, valves, heat exchanger, and process piping are included to provide a complete system.
Grant/Hop Back
Our 25 gallon grant/hop back provides an accessible location to take wort samples during the lautering process. The grant is also used by many brewers to dry hop their wort after the boil is complete. High and low level sensors inside the vessel control the main transfer pump to maintain the correct flow in the process. The grant/hop back has a removable wedge wire false bottom for easy cleaning and sanitation.
Brewers Platform
The brewer’s platform is custom fitted to match each brewhouse system. Made from a perforated, non-slip fiberglass material the brewing platform allows the brewer easy access to the control panel and manways on top of the vessels. The brewhouse system has been designed to minimize elevation and only requires three steps from ground to top of platform.
Control Panel
The brewing control panel allows the brewer to set HLT temperature setpoint and monitor mash tank and brew kettle temperatures. Transfer pump mode and speed are also controlled at the panel. Each control panel is built in the USA, prewired and tested in our shop, and is UL listed for the specific job location.
Keg Washer The custom-fitted keg washer allows 2 kegs to be cleaned and sanitized at the same time. The keg washer rolls into place along the front of the brewhouse and utilizes the main transfer pump to circulate cleaner through the kegs. An experienced operator can clean up to 20 kegs per hour with this system.